Q-Logic 64 Manual de usuario Pagina 80
- Pagina / 244
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
5 – Diagnostics/Troubleshooting
POST Diagnostics
5-2 59043-03 A
D
5.1.1.2
Maintenance Mode Pattern
Steady illumination indicates that the switch is in maintenance mode, which
returns the switch IP address to 10.0.0.1. From maintenance mode, you may
reload firmware, reset the password to the factory default, and remove a corrupt
configuration.
5.1.1.3
Internal Firmware Failure Blink Pattern
An internal firmware failure blink pattern is 2 blinks per second followed by a two
second pause. The 2-blink error pattern indicates that the firmware has failed, and
that the switch must be reset. Press and release the Maintenance button to reset
the switch.
5.1.1.4
Fatal Error Blink Pattern
A fatal error blink pattern is 3 blinks per second followed by a two second pause.
The 3-blink error pattern indicates that a fatal error has left the switch inoperable.
If a fatal error occurs, contact your authorized maintenance provider. Press and
release the Maintenance button to reset the switch.
5.1.1.5
Configuration File System Error Blink Pattern
A configuration file system error blink pattern is 4 blinks per second followed by a
two second pause. The 4-blink error pattern indicates that a configuration file
system error has occurred, and that the configuration file must be recreated. Refer
to ”Recovering a Switch” on page 5-12 for more information.
To recreate the configuration file, do the following:
2 seconds
1 second
2 seconds
1 second
2 seconds
1 second
- Installation Guide 1
- Document Revision History 2
- Table of Contents 3
- Section 3 Planning 4
- Section 4 Installation 4
- 59043-03 A Page v 5
- Section 6 Removal/Replacement 6
- Appendix A Specifications 6
- 59043-03 A Page vii 7
- 59043-03 A Page ix 9
- Page x 59043-03 A 10
- Introduction 11
- Related Materials 12
- Safety Notices 13
- Sicherheitshinweise 13
- 1 – Introduction 14
- Communications Statements 14
- 1-4 59043-03 A 14
- CE Statement 15
- VCCI Class A Statement 16
- BSMI Class A Statement 16
- Laser Safety Information 17
- Accessible Parts 18
- Pièces Accessibles 18
- Zugängliche Teile 18
- General Public License 19
- Preamble 19
- 1-10 59043-03 A 20
- 59043-03 A 1-11 21
- 1-12 59043-03 A 22
- 59043-03 A 1-13 23
- 1-14 59043-03 A 24
- 59043-03 A 1-15 25
- Technical Support 26
- Availability 26
- Training 26
- Contact Information 26
- General Description 27
- Chassis Hardware 28
- 2 – General Description 29
- 59043-03 A 2-3 29
- Chassis Controls and LEDs 30
- Maintenance Button 30
- Resetting a Switch 31
- Chassis LEDs 32
- Over Temperature LED (Amber) 32
- Fan Fail LED (Amber) 32
- Heartbeat LED (Amber) 33
- Input Power LED (Green) 33
- Fibre Channel Ports 33
- Port Status LED 34
- Port Modes 35
- Fabric Ports 35
- Expansion Port 35
- Ethernet Port 35
- Serial Port 36
- Figure 2-10. Fans 39
- Switch Management 40
- Planning 41
- Multiple Chassis Fabrics 44
- Common Topologies 45
- Performance 46
- Distance 46
- Bandwidth 47
- Device Access 48
- Soft Zones 49
- 3 – Planning 50
- 3-10 59043-03 A 50
- Fabric Security 51
- User Account Security 51
- Device Security 52
- 59043-03 A 3-13 53
- Port Group: Group_Port 53
- 59043-03 A 3-15 55
- 3-16 59043-03 A 56
- MS Group: Group_1 56
- Fabric Services 57
- 3-18 59043-03 A 58
- Installation 59
- Environmental Conditions 60
- Installing a Switch 60
- Mount the Switch 61
- 4 – Installation 62
- 4-4 59043-03 A 62
- 59043-03 A 4-5 63
- Install SFP Transceivers 64
- 59043-03 A 4-7 65
- 4-8 59043-03 A 66
- Ethernet Connection 68
- Serial Connection 68
- Install SANbox Manager 69
- 4-12 59043-03 A 70
- 4-14 59043-03 A 72
- Configure the Switch 73
- Configure the Ports 74
- Cable Devices to the Switch 74
- Install Firmware 75
- Powering Down a Switch 78
- Diagnostics/Troubleshooting 79
- Maintenance Mode Pattern 80
- Fatal Error Blink Pattern 80
- Port Status LED Indications 83
- E_Port Isolation 84
- Excessive Port Errors 85
- POST Diagnostics 86
- 5-8 59043-03 A 86
- Chassis Diagnostics 87
- Fan Fail LED is Illuminated 88
- 59043-03 A 5-11 89
- Recovering a Switch 90
- Maintenance – Exit 91
- Maintenance – Image Unpack 91
- 5-14 59043-03 A 92
- 59043-03 A 5-15 93
- 5-16 59043-03 A 94
- Removal/Replacement 95
- CPU Module 96
- Removing the CPU Module 96
- Installing the CPU Module 98
- I/O Blades 101
- Cross-Connect Blades 105
- Removing a CC Blade 106
- Figure 6-5. CC Blade Removal 107
- Installing a CC Blade 108
- 6 – Removal/Replacement 109
- 59043-03 A 6-15 109
- Power Supply Modules 110
- 6-18 59043-03 A 112
- Removing a Fan 113
- Installing a Fan 114
- Specifications 115
- Maintainability 116
- Fabric Management 117
- Dimensions 117
- Electrical 117
- Environmental 118
- Regulatory Certifications 119
- A – Specifications 120
- A-6 59043-03 A 120
- 59043-03 A A-7 121
- A-8 59043-03 A 122
- Command Line Interface 123
- Command Syntax 124
- Commands 125
- Admin Command 126
- Alias Command 127
- B – Command Line Interface 128
- B-6 59043-03 A 128
- Config Command 129
- B-8 59043-03 A 130
- 59043-03 A B-9 131
- Date Command 132
- Fallback Command 133
- Group Command 134
- B-14 59043-03 A 136
- 59043-03 A B-15 137
- Hardreset Command 138
- Help Command 139
- B-18 59043-03 A 140
- History Command 141
- Hotreset Command 142
- Hotswap Command 143
- B-22 59043-03 A 144
- Image Command 145
- Lip Command 146
- Passwd Command 147
- Ping Command 148
- Ps Command 149
- Quit Command 150
- Reset Command 151
- Security Command 157
- B-36 59043-03 A 158
- 59043-03 A B-37 159
- Securityset Command 160
- 59043-03 A B-39 161
- Set Command 162
- 59043-03 A B-41 163
- Set Config Command 164
- B-50 59043-03 A 172
- 59043-03 A B-51 173
- B-52 59043-03 A 174
- 59043-03 A B-53 175
- Set Log Command 176
- 59043-03 A B-55 177
- B-56 59043-03 A 178
- Set Port Command 179
- Set Setup Command 180
- 59043-03 A B-61 183
- B-62 59043-03 A 184
- Show Command 185
- B-64 59043-03 A 186
- B-68 59043-03 A 190
- 59043-03 A B-69 191
- B-70 59043-03 A 192
- 59043-03 A B-71 193
- B-72 59043-03 A 194
- 59043-03 A B-73 195
- B-74 59043-03 A 196
- 59043-03 A B-75 197
- B-76 59043-03 A 198
- 59043-03 A B-77 199
- Show Config Command 200
- 59043-03 A B-79 201
- B-80 59043-03 A 202
- Show Log Command 203
- B-82 59043-03 A 204
- Show Perf Command 205
- B-84 59043-03 A 206
- Show Setup Command 207
- B-86 59043-03 A 208
- 59043-03 A B-87 209
- Shutdown Command 210
- Test Command 211
- Uptime Command 214
- User Command 215
- B-94 59043-03 A 216
- 59043-03 A B-95 217
- Whoami Command 218
- Zone Command 219
- B-98 59043-03 A 220
- 59043-03 A B-99 221
- B-100 59043-03 A 222
- Zoneset Command 223
- B-102 59043-03 A 224
- 59043-03 A B-103 225
- Zoning Command 226
- 59043-03 A B-105 227
- B-106 59043-03 A 228
- 59043-03 A B-107 229
- B-108 59043-03 A 230
- Glossary 231
- Glossary-2 59043-03 A 232
- 59043-03 A Glossary-3 233
- Glossary-4 59043-03 A 234
- 59043-03 A Glossary-5 235
- Glossary-6 59043-03 A 236
- Numerics 237
- Index-2 59043-03 A 238
- 59043-03 A Index-3 239
- Index-4 59043-03 A 240
- 59043-03 A Index-5 241
- Index-6 59043-03 A 242
- 59043-03 A Index-7 243
- Index-8 59043-03 A 244
© 2020, manymanuals.es. Todos los derechos reservados | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales