Q-Logic QLA12160 Manual de usuario Pagina 1

Hardware Installation Guide for the QLA12160 Board64-Bit PCI Dual SCSI Host Adapter Boardfor the PCI BusDC8151101-00 CSeptember 14, 2001

Setting the SCSI Termination 2 – Hardware Installation2-2 BC8151101-00 CFigure 2-1 identifies the QLA12160 board components referenced throughout this

2 – Hardware Installation Installation in the ComputerBC8151101-00 C 2-3light to the J9 jumper block on the QLA12160 board (pins 1 and 4 are positive)

Installation in the Computer 2 – Hardware Installation2-4 BC8151101-00 C5. Unscrew and remove the slot cover. Retain the screw to use when you install

2 – Hardware Installation Installation HelpBC8151101-00 C 2-5See the Software Installation Guide for the QLA12160 Board on the QLogic web site http://

Installation Help 2 – Hardware Installation2-6 BC8151101-00 C

DC8151101-00 B 3-1Section 3 Troubleshooting3.1Problems After InstallationThere are three types of installation problems that can cause your QLA1

SCSI Problem Checklist 3 – Troubleshooting3-2 DC8151101-00 B3.4SCSI Problem Checklist Is the SCSI bus termination for the QLA12160 board set correctl

DC8151101-00 C A-1Appendix A Fast!UTILA.1IntroductionThis appendix provides detailed configuration information for advanced users who want to customiz

Configuration Settings A – Fast!UTILA-2 DC8151101-00 CA.2.1Host Adapter SettingsFrom the Configuration Settings menu in Fast!UTIL, select Host Adapter

A – Fast!UTIL Configuration SettingsDC8151101-00 C A-3❑ Safe. All optimal configuration settings are disabled and all attached devices work in minimal

QLogic CorporationPage ii DC8151101-00 CInformation furnished in this manual is believed to be accurate and reliable. However, QLogic Corporation ass

Configuration Settings A – Fast!UTILA-4 DC8151101-00 CNOTE: These settings apply to each SCSI ID individually. Disconnects OK. When set to Yes, the d

A – Fast!UTIL Configuration SettingsDC8151101-00 C A-5 Negotiate Synchronous. When set to Yes, the QLA12160 board negotiates synchronous data transfe

Configuration Settings A – Fast!UTILA-6 DC8151101-00 C SCSI termination Termination for the QLA12160 board can be set in one of three ways:❑ Automati

A – Fast!UTIL Configuration SettingsDC8151101-00 C A-7connected to the other connector. Use this setting for the QLA12160 board’s port two (J2) when t

Scan SCSI Bus A – Fast!UTILA-8 DC8151101-00 CA.2.6Restore Default SettingsThe Restore Defaults option from the Configuration Settings menu restores th

A – Fast!UTIL Using SCSI-1 DevicesDC8151101-00 C A-93. Select SCSI Device Settings. A window displays the settings for each SCSI device. Make the foll

Using SCSI-1 Devices A – Fast!UTILA-10 DC8151101-00 C

DC8151101-00 C B-1Appendix BSCSI TerminationB.1Setting the SCSI TerminationThe first and last physical SCSI devices on each end of the SCSI bus must b

Termination (Jumpers) for the QLA12160 B – SCSI TerminationB-2 DC8151101-00 CThe QLA12160 board jumper block is illustrated in figure B-1..Figure B-1.

DC8151101-00 C C-1Appendix CSpecifications Table C-1. QLA12160 Board Operating EnvironmentEnvironment Minimum MaximumOperating temperature 0°C (32°F)

DC8151101-00 C Page iiiTable of ContentsSection 1 Introduction1.1 Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

C – SpecificationsC-2 DC8151101-00 CConnectors 68-pin, high-density, internal SCSI-2 connector (port one)Two 68-pin, external VHDCsForm factor 17.78cm

Table of Contents QLA12160 Hardware Installation GuidePage iv DC8151101-00 CAppendix B SCSI TerminationB.1 Setting the SCSI Termination . . . . . .

DC8151101-00 C 1-1Section 1 IntroductionNOTE: This installation guide applies to the following QLogic host adapter boards, collectively referred

Features 1 – Introduction1-2 DC8151101-00 CThe QLA12160 board supports Ultra, Ultra2, and Ultra3 transfer speeds. The board can connect computers to o

1 – Introduction FeaturesDC8151101-00 C 1-3 Support for LVD mode Support for up to 30 LVD SCSI devices (15 per channel) Support for logical unit nu

Features 1 – Introduction1-4 DC8151101-00 C

BC8151101-00 C 2-1Section 2 Hardware Installation2.1Preinstallation ProceduresBefore installing your QLA12160 board, take the time to read this i