Q-logic Keyless Entry Alarm Upgrade Module APS-30 Manual de usuario descargar pdf

KEYLESS ENTRY ALARM UPGRADE MODULE

INSTALLATION INSTRUCTIONS

PRE - INSTALLATION NOTES :

STAND ALONE PASSIVE ALARM

When installing the APS-30 as a stand alone passive alarm system, the dip switches must be set as follows;

Dip Switch#1=ON

Dip Switch#2=ON

Dip Switch#3=OFF

Dip Switch#4=OFF

Dip Switch#5=OFF

Dip Switch#6=OFF

PASSIVE / ACTIVE ARMING SELECTION : DIP SWITCH # 1

This alarm can be programmed to operate as either a " PASSIVE " or " ACTIVE " arming security system.

As a passive arming system, the alarm will automatically arm 30 seconds after the ignition key is turned off, one door is opened, then

all doors are closed. Additionally, if a door has been left opened, or if one of the trigger zones is defective, the system will always arm

10 minutes after the ignition key has been turned off, and ignore the defective trigger zone.

As an active arming system, the alarm will arm only when the vehicle’s doors have been locked using the existing OEM Keyless Entry

Transmitter.

The system is shipped from the factory in the active arming mode, and to select the passive arming mode, move dip switch#1tothe"

ON " position.

1 OR 2 WIRE DISARM INPUT SELECTION : DIP SWITCH # 2

This alarm can be programmed for either 1 wire or 2 wire disarm operation.

Many OEMkeyless entry systems use on - board door unlock relays, which usually results in the ability to disarm the aftermarket security

upgrademodule by unlocking thedoors using the door panel unlock switch.Wiring the system for2 wire disarm willeliminate this problem.

The system is shipped from the factory in the 2 wire disarm mode, and to select the 1 wire disarm mode, move dip switch#2tothe"

ON " position.

HORN OR SIREN OUTPUT SELECTION : DIP SWITCH # 3

This system provides an output that should be used to drive the siren, but can be programmed to pulse the vehicle's horn.

When utilizing the horn, an additional relay is required. Caution: on many vehicles the factory horn is not designed

for continuous use, and it is recommended that the siren is used for these vehicles. Check to see if the horn in the vehicle

is the same part that is used in a vehicle with the factory installed security system.

DIP SWITCH SETTINGS

PASSIVE ARMING

1 WIRE DISARM

HORN MODE

INSTANT TRIGGER

- ARM INPUT

VOLTAGE SENSE

ON OFF

ACTIVE ARMING

2 WIRE DISARM

SIREN MODE

ENTRY DELAY

+ ARM INPUT

HARDWIRE

Model APS-30

1 2 3 4 5 6

Indice de contenidos

Pagina 1 - Model APS-30

KEYLESS ENTRY ALARM UPGRADE MODULEINSTALLATION INSTRUCTIONSPRE - INSTALLATION NOTES :STAND ALONE PASSIVE ALARMWhen installing the APS-30 as a stand al

Pagina 2

This alarm can be programmed to drive an electronic siren, or pulse the vehicle's horn.Inthe siren mode, theaudible output will deliver a switche

Pagina 3

SCENARIO ASCENARIO BSCENARIO CSCENARIO DRESULTAPS-30 DISARMSNO CHANGE IN ALARMSTATUSAPS-30 DISARMSNO CHANGE IN ALARMSTATUSDISARM #2RED / BLACKWIRENEGA

Pagina 4 - WIRING THE SYSTEM :

Two pin switches are included for use in protecting the hood and trunk ( or hatchback ) of the vehicle.The switches must always be mounted to a ground

Pagina 5 - 4 PIN CONNECTOR

Connect this wire to the DARK BLUE wire from the push-button manual override switch. Connect the BLACK wire from the switchto chassis ground.BLACK WIR

Pagina 6 - TYPICAL ONE-STEP DIAGRAM

Printed in Taiwan Audiovox Corp., 150 Marcus Blvd. Hauppauge, N.Y. 11788 Form No.128-4515+FACTORYREMOTEKEYLESSENTRY MODULE+TYPICAL 2-S

Comentarios a estos manuales

Sin comentarios

Q-logic Keyless Entry Alarm Upgrade Module APS-30 Manual de usuario

Busca en linea o descarga Manual de usuario para Para El Coche Q-logic Keyless Entry Alarm Upgrade Module APS-30. Q-Logic Keyless Entry Alarm Upgrade Module APS-30 User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales